18000 LB. CAPACITY JACKSTANDS

Our most popular option! Stands are used to support vehicles for tire and brake work allowing removal of the the Mobile Lifts to service other vehicles. Tripod Base. Easily adjustable at 4” increments by removal and replacement of positioning pin. ( 50”-82” model employs spring assisted placement) Fine adjustment over a 6” range by means of a 2.25-4 ACME threaded adjustment Rod ( to ensure proper placement.

• Easily moved by two 4” Diameter Wheels.
• Fold Down Handle on Tall and Medium Models
• Available in 3 basic heights:
• Tall ( 50”-82”)
• Medium ( 30”-50”)
• Short ( 18”-30”)
• Available in Different Head Types:
• U-Shaped Formed Head (cradle)
• Replaceable Rubber Pad Head
• Wood Top

LT-15 FRONT/REAR ADAPTER

LT-15 Front/Rear Adapter kit can be used with 1 pair of  WE-18 column lifts and is suitable for lifting light trucks and vans 15000 Lbs. or less. Kit includes 2 base assemblies with adjustable adapters.

PEN-4B PENDANT OPERATOR STATION

Remote pendant with 50’ cable allows operation of the mobile lift while monitoring the lifting of the vehicle from various vantage points.

PEN-4BQR PENDANT OPERATOR STATION W/QUICK RELEASE

Same as above but with quick release.

WDH-1000 HIGH LIFT WHEEL DOLLY

High Lift Wheel Dolly, 1000 LB Capacity used for the removal and installation of single, tandem and duplex tires and wheels which are mounted on trucks that are supported above ground level. Allows easy rotation of wheels for alignment of bolt pattern, has side to side adjustment for aligning.

HTJ/A-2000 TRANSMISSION JACK ( AIR/HYDRAULIC)

Hydraulic transmission jack, 2000 Lb. Capacity used for the removal, installation and transportation of heavy duty truck transmissions that are raised by in-ground and above ground lifts. Adjustable saddle with corner brackets and chain, foot operated pump and lowering pedals allow for use of both hands for positioning.

HTJ-2000 TRANSMISSION JACK (HYDRAULIC)

Same as Above, but without the air/hydraulic foot operated pump.

VLB36-120 VEHICLE LIFTING BEAM

This Frame and Vehicle Engaging Beam, 36000LB Capacity, is utilized when the vehicle or other objects being lifted do not have axle or wheel pickup points. Frame Engaging Beam is 1 piece with 2 adapter-receivers (position-adjustable on beam) and 6 formed-top pickup adapters at various heights. Shipped complete with 2 removable caster trays and two steering handles for ease of moving in and out of service bays.

PWEB – WHEEL ENGAGING BEAM FOR PELICAN ( OR SIMILAR)

Wheel Engaging Beam  is utilized with four columns of the WE-18. Easily engaged by the WE-18 after the vehicle has been driven into place. System consists of 1 piece beam with 1 removable approach ramp. Shipped with two removable caster trays and  two steering handles for ease in moving in and out of service bays.

PEL-18 SWEEPER ADAPTER ASSY. – FOR PELICAN (OR SIMILAR)

PEL-18 is utilized with three columns of the WE-18. 18000 LB Capacity. 1 piece designed to set between forks providing a flat continuous surface for engaging frames or other suitable contact points.

FL-ADP FORKLIFT ADAPTER OPTION

Allows utilization of 1 pair of WE-18’s to hoist and service forktrucks with a low ground clearance. Kit includes 2 lifting plates and 4 ( removeable) ramps allowing forktruck to drive over WE-18 Lifting forks. Forktrucks having adequate ground clearance do not require ramps.

WEB 36-120  WHEEL ENGAGING BEAM

Wheel Engaging Beam, 36000 Lb. Capacity is intended to enhance the versatility of the WE-18 Mobile Column Lift and employed where vehicle serviced cannot be hoisted by typical means ie: due to the presence of wing plows or when wheels typically used for lifting are significantly recessed inside body panels of vehicle. 

SYSTEM INCLUDES:

1 piece drive-over, 2 adjustable approach ramps. System shipped complete with 2 removable caster trays and 2 steering handles for ease in moving in and out of service bays.

UHS-2000  UNDER HOIST STAND

Under Hoist Stand. 2000 Lb. Capacity for replacing exhaust systems, shock absorbers and MacPhearson struts. Hydraulic power will assist in unfreezing froze spring shackles, aligning wheels and steering gear adjustments.

APU-18  MANUAL HYDRAULIC PUMP KIT

10,000 LB. PSI  Hand Operated porta-power with quick release coupling used to manually dis-engage mechanical safety on the WE-18 during power failures of for other maintenance requirements when manual lowering is necessary.